Kilns & Firing Accessories

Slurry, air setting, cone 10 mortar and patching compound. Sodium Silicate is the binder and requires no heating to set. Can be used for floors, arches, and walls, but is excellent for repairs, damper guides on the tops of kiln arches, and areas where there is limited heat to set the mortar. When handling, wear latex or rubber gloves and eye protection. This mortar sets up very fast, so you need to have a clean bucket of water and a sponge handy to clean up as you go. This product can settle and may need to be mixed before using. As with all mortars, any sulfates that come to the surface of a kiln wall after drying must be removed with a stiff brush. If these sulfates are not removed, they will form a glaze on the brick surface. Ship Wt. is 19 lbs.

Slurry, air setting, cone 10 mortar and patching compound. Sodium Silicate is the binder and requires no heating to set. Can be used for floors, arches, and walls, but is excellent for repairs, damper guides on the tops of kiln arches, and areas where there is limited heat to set the mortar. When handling, wear latex or rubber gloves and eye protection. This mortar sets up very fast, so you need to have a clean bucket of water and a sponge handy to clean up as you go. This product can settle and may need to be mixed before using. As with all mortars, any sulfates that come to the surface of a kiln wall after drying must be removed with a stiff brush. If these sulfates are not removed, they will form a glaze on the brick surface. Ship Wt. is 52 lbs.

The EnviroVent 2 is a Downdraft Ventilation System designed to extract fumes from your electric kiln and vent them outdoors before they have a chance to enter the room. Because it is a DownDraft Ventilation System, the EnviroVent 2 also improves the firing atmosphere in the kiln while it is protecting you from the odorous fumes that can be emitted from certain clay bodies and glazes when they are fired. Ship wt. is 17 lbs.

The EnviroLink was developed by engineers at Skutt to provide kiln owners with the ability to automatically control the Skutt EnviroVent and EnviroVent 2. The device utilizes a programmable power output (OUTPUT 4) on Skutt KilnMaster and GlassMaster Controllers to turn on/off the EnviroVent and EnviroVent 2. The kiln may be programmed to control the vent during any segment of a Ramp/Hold Program or during preset times of a ConeFire or Glass Fire Mode program. Ship wt. is 2 lbs.

The Dual Intake Kit allows you to vent 2 kilns up to 12 cubic feet each, or one kiln between 12 and 24 cubic feet, with one EnviroVent 2 Motor.

8' x 3" ducting used to extend original duct.

Element only. Does not include porcelain block or lead wires. Instructions included. 6" in length. Ship wt. is .25 lbs.

This Pyrometer comes with a Type K thermocouple, thermocouple mounting block, 5 feet of thermocouple wire, and a pyrometer flange for mounting the thermocouple to the kiln. The Pyrometer comes with a case that can be mounted to the wall. It also has a flip out back so that it can be set on a table or shelf. Since it is Dual Input, you can purchase an additional thermocouple package and monitor two kilns. It even remembers the minimum and maximum temperatures recorded in a firing. It is rated to Cone 10 with a plus or minus 0.4% of reading accuracy. Ship wt. is 1 lb.

This upgrade package allows you to upgrade an existing Skutt kiln. Click on "Details" to find the right upgrade for your kiln.

Electrical Requirements: Single Phase, 115 Volts, 15 Amps, 1725 Watts, Copper Wire Size: 12, Breaker Size: 20, NEMA Receptacle Configuration: 5-15, .6 cubic feet of 1700F power. Inside Chamber Dimensions: 15" wide x 6.5" deep. Includes 13" round shelf, kiln wash, kiln paper, and 3 short posts. Shipping Weight is 100 lbs.

A Current Sensor is required for Skutt touchpads that have a red display.

The Easy View is a new optional feature that makes it easier to see and program your controller by angling the touchpad up. It can be added to any KilnMaster kiln in minutes without having to remove any wires from the controller. Ship wt. is 4 lbs.

Electrical Requirements: Single Phase, 115 Volts, 20 Amps, 2300 Watts, Copper Wire Size: 10, Breaker Size: 30, NEMA Receptacle Configuration: 5-20, .8 cubic feet of Cone 6 power. Inside Chamber Dimensions: 11" wide x 13.5" deep. Uses a 6 sided full shelf (C-100 - 9.25" x 10" x 1/2") or 3 sided half shelf (C-100 half - 9.25" x 5" x 1/2"). APM Elements Upgrade and pricing available upon request. Shipping Weight is 88 lbs.

Electrical Requirements: Single Phase, 240 Volts, 20 Amps, 3600 Watts, Copper Wire Size: 10, Breaker Size: 30, NEMA Receptacle Configuration: 14-30, 1.4 cubic feet of Cone 8 power. Inside Chamber Dimensions: 14.38" wide x 13.5" deep. Uses a 13" x 5/8" round shelf or a 13" x 6.5" x 5/8" half round shelf. APM Elements Upgrade and pricing available upon request. Shipping Weight is 95 lbs.

Electrical Requirements: Single Phase, 208 Volts, 20 Amps, 3600 Watts, Copper Wire Size: 10, Breaker Size: 30, NEMA Receptacle Configuration: 14-30, 1.4 cubic feet of Cone 8 power. Inside Chamber Dimensions: 14.38" wide x 13.5" deep. Uses a 13" x 5/8" round shelf or a 13" x 6.5" x 5/8" half round shelf. APM Elements Upgrade and pricing available upon request. Shipping Weight is 95 lbs.